Helpful tips

Why does my radio have power but no sound?

Why does my radio have power but no sound?

Possible Cause: Radio volume is down or radio is muted. Each speaker needs its own positive and negative connection from the radio. Shorted or grounded speaker wires or speaker terminals.

Why is my car radio displays but no sound?

Typically when a car stereo produces no sound it’s usually caused by a shorted or grounded wire, defective speakers, faulty head unit/fuses, or setup is not yet complete with your radio unit.

Why did my radio sound stop working?

Blown Fuse: One of the most common reasons for a car radio to stop working is a blown fuse. Damaged Speaker Wires – If your car radio will turn on, but you’re not getting sound (or are getting sound from just one or two speakers), the culprit is most likely a speaker wire that’s been damaged.

How do I reset my Hyundai sound system?

If Your Hyundai IX35 radio is not working then the first thing that You will want to do is reset the radio. To do this You will need to press in on the volume knob that is located on the dash and wait for the screen to turn off and back on.

Is there a fuse for radio sound?

A car radio will have at least one fuse to protect the unit from things like power surges or other electrical issues. If too much current is sent to the audio system, this fuse will blow out and disconnect the circuit to save the main radio.

Where is the fuse for the radio?

Usually located in or around the instrument panel near the dash, fuses can also be found under the hood and even under the rear seat. Next time your radio, lights or other device stops working, chances are a blown fuse is the culprit.

Which fuse is for the radio?

Most low-powered radios can use a 20-amp fuse without any issues. However, for high-powered stereos — those that produce 100 watts of power or more — you may have to use a 25- or 30-amp fuse. You may be able to use a wire clasp or harness already under the dash to secure the wiring from the radio to the fuse box.

How do you know if your radio fuse is blown?

Touch the red wire on the multimeter to a pole on the fuse. Touch the black wire to another pole. If you hear a beeping sound after doing this, then the fuse is likely in good condition, and there is probably a problem with the capacitor. If you don’t hear a beep, then the fuse is blown and needs to be replaced.

How do you fix a blown fuse in a car radio?

Changing a fuse in your car is similar to changing one at home.

  1. Locate your car’s fuse panel.
  2. Take off the fuse panel’s cover.
  3. Locate the blown fuse.
  4. Remove the broken fuse.
  5. Insert a replacement fuse of the correct amperage—make note of the fuse panel and your owner’s manual on this one.

What number is the fuse for the radio?

Why is my audio not working on my Hyundai Sonata?

The problem could be with the radio but since the radio does power up and work I’m assuming that you have the optional factory external amplifier and that is more likely where the problem is. Sound leaves the radio and to the amplifier, which then sends signals to the speakers, whether it’s audio or cell phone or navigation.

Is the XM on my Hyundai Sonata working?

Hyundai veracruz radion will not activate xm feature. 2008. Hyundai veracruz radion will not activate xm feature.  read more Eric Retired N/A 46,441 satisfied customers

What do you do when there is no sound in your Hyundai Elantra?

Pull the fuse for the audio system, wait about a minute, and then put it back in. It will reset the sound system. Quirky fix, but it will work. My 2012 does the same thing.

Is there a hard reset on Sonata Hybrid?

Note: This does not apply to Sonata Hybrid models. This fault requires no part replacement, and is a software glitch that can be rectified by a ‘hard reset’. To perform the hard reset, simply disconnect the vehicles negative battery terminal, wait 15 minutes, and reconnect the negative battery terminal.