Why does it take so long to connect to virtual disk service?

Why does it take so long to connect to virtual disk service?

Disk Management takes a long time to load – If Disk Management takes a long time to load, the issue might be caused by your hardware. Disk Management could not start VDS – This issue can occur if the required services aren’t running. To fix the problem, be sure that the VDS service is enabled on your PC.

Can you restart Virtual Disk Service?

Type services. In the Services Window, look for Virtual Disk service and Stop it. Restart the computer and Start the Virtual Disk service and set it to Automatic. Restart the computer and it check if it works.

What happens if virtual disk service stopped?

If yes, then the Virtual Disk service stopping can cause this type of a backup failure. Additionally, check what time the Backup Exec daily maintenance is set to run. Do ensure it does not conflict with the backup job timings. If running an AV scan, set it to exclude from scanning the BE processes.

What is Virtual Disk Service error?

Virtual Disk Service error: There is not enough usable space for this operation. This error often occurs when there is no unused free space or not enough unallocated space available on a hard disk for some specific operations, such as to extend a partition or to create a primary partition using DiskPart utility.

Can’t connect to virtual disk service?

Error “Unable to connect to Virtual Disk Service” may also occur if the remote computer doesn’t support VDS or you can’t establish a connection to the remote computer because it is locked by Windows Firewall.

How do I enable virtual disk?


  1. Enter the System Setup by pressing F2 during system start.
  2. Click on Device Settings.
  3. Click on the desired RAID controller device.
  4. Click on Configuration Management.
  5. Click on Create Virtual Disk.
  6. The following list of options are now displayed to define the Virtual Disk parameters:
  7. Click on Select Physical Disks.

Can I disable Virtual Disk Service?

type Start + R and run services. msc from the popup window. Scroll down until you find the Disk Defragmenter service in the list. Its startup type should be Disabled .

How do I get rid of virtual disk service error?

Best 2 Ways to Fix “Virtual Disk Service Error Clean Is Not…

  1. The cause: why clean is not allowed on the disk.
  2. Then you could create a new partition on the drive to solve this problem.
  3. Tick USB Boot Device to create bootable USB drive.
  4. Press Proceed.
  5. Choose a proper deletion method, hit OK.

How do I enable virtual disk services?

How do I enable virtual disk services? Press “Windows + R” keys simultaneously to call out Run box. Type “msc” in the Runbox and press Enter key to open Windows Services Manager. Scroll down to find Virtual Disk service.

Should the virtual disk service be running?

In normal configuration, the VDS service in Windows is configured to start manually (Startup type – Manual). It means that it should be run if necessary if other apps access it. However, in our case it doesn’t happen on some reason. Windows could not start the Virtual Disk service on Local Computer.

How do I fix virtual disk error volume size is too big?

If you try to format hard drive larger than 32GB, you can only see NTFS in drop-down menu of File system. Therefore, to fix the“the volume size is too big for FAT32”error, you need to switch to the third-party free partition software: AOMEI Partition Assistant Standard.

How do I fix virtual disk service error not found?

An acceptable solution is to contact your OEM support to seek professional assistance. In addition, you would get the “The object is not found” error in Diskpart when the disk is failing and cannot hold a partition anymore. You can run CHKDSK /f on that disk to check hard drive for errors.

Where do I find connecting to virtual disk service?

When I go to computer management and click on disk management, there is nothing in the menu, but at the bottom, it says “connecting to virtual disk service…” endlessly. Also, I can’t access system restore nor install applications that require restore points…when I unplug the drive, I have no problems after a restart.

What to do if disk management cannot connect to virtual disk?

If you are stuck in Disk Management connecting to Virtual Disk Service, you can first remove or eject external storage devices one by one to identify the problematic device. Some users repair Disk Management by removing external storage devices. I had the same problem. I noticed that I had a windows phone plugged into a USB port for charging.

How to connect virtual disk to run box?

Step 1: Press ” Windows + R ” keys simultaneously to call out Run box. Step 2: Type ” services.msc ” in the Run box and press Enter key to open Windows Services Manager. Step 3: Scroll down to find Virtual Disk service. Step 4: Double-click this service to open it.

Why does MS virtual disk service keep hanging?

Well, the one driver that is troublesome is the MS Virtual SCSI Disk drive itself (once the VDS locks up, that device cannot be deleted or unmounted), but since it works in Safe mode, then it has to be something else. Was this reply helpful? Sorry this didn’t help. Great! Thanks for your feedback. How satisfied are you with this reply?